Central vacuum supply for economical rotor blade production

Groß-Rotorblattfertigung GmbH achieved energy savings of at least 50 percent for the vacuum supply for rotor blade production thanks to the use of a new centralized vacuum system. The plant, which belongs to the ENERCON Group, was also able to avoid noise and heat emissions in the production hall by centralizing vacuum generation for resin infusion. The vacuum supply, which was designed and implemented by Dr.-Ing. K. Busch GmbH, is housed in a separate room and provides the vacuum for all of Groß-Rotorblattfertigung.

ID: 1550653
recent pressrelease next pressrelease

(businesspress24) - ENERCON has been producing rotor blades for wind turbines on the site of a former steel foundry in Magdeburg-Rothensee since 2001. Today there are six different ENERCON Group companies located there with a total of around 2,500 employees that deal with building components for wind turbines. Gro in a sandwich construction. These are covered with a plastic foil that is applied in a way that creates an air-tight seal along the edges of the form. For safety reasons, a second foil is laid on top that is also applied in a manner that creates an air-tight seal. This is intended to prevent negative effects on the process or on the quality of the component to be manufactured due to leaks that may occur. Afterwards, vacuum is applied to remove/extract the air between the form and the plastic foils. After testing for leaks, resin infusion into the component begins. Due to the vacuum, the resin flows into all areas and spaces in the component and thus completely saturates it. After the resin is tempered and hardened, the form can be aerated back to atmospheric pressure and the component can be removed.

In the past, decentralized vacuum units with oil-lubricated rotary vane vacuum pumps were used. These pumps were sometimes permanently installed or used as mobile units at different forms. They supplied the individual forms with vacuum using tubes. Overall, 36 rotary vane vacuum pumps were used to evacuate forms and infuse the components, which was performed in three-shift continuous operation at Gro

Thomas Giesecke was responsible for the process planning department and was searching for a technically optimized solution in 2016. The disadvantages of the existing vacuum supply were due to the fact that waste heat from the rotary vane vacuum pumps was emitted directly into the production hall. Noise emission in the workplace was also very high due to the number of vacuum pumps. In addition, Thomas Giesecke was looking for a vacuum supply that would work without oil as an operating fluid because oils or oil fumes have a separating effect on the glass fibre and core materials and can therefore negatively affect the production process.


His vision was also to have a certain vacuum level continually available that would make manual regulation unnecessary and thus make the process stable, safe and transparent.
After precisely analysing the current state, the vacuum specialists from Dr.-Ing. K. Busch GmbH designed a vacuum supply system consisting of individual dry, oil-free COBRA NX screw vacuum pump vacuum modules. This system was constructed in such a way that its dimensions fit into an already existing separate engineering room. The control cabinet with the control system is also located in this room.

The system is set up so that four screw vacuum pumps are connected to a ring main that runs through the entire Gro, this vacuum circuit serves to infuse the resin into the rotor blade components with the same vacuum level.

Together with Thomas Giesecke and his team, Marcus Kempf as programmer and Dirk Sztuck as project coordinator, the vacuum specialists from Busch optimized the vacuum supply so that the so-called vacuum control panels are interposed between the individual forms and both of the vacuum circuits. Inside are valves that automatically switch from one vacuum circuit to the other when initial evacuation is finished and resin infusion begins. The two-circuit solution and intelligent vacuum control technology in the vacuum control panels directly at the rotor-blade forms enable reliable and safe implementation of the resin infusion process. This control system also enables all process data to be recorded and saved.

The level of vacuum required varies widely because the processes at all connected forms are performed at different times. The demand-based control system continually recognizes the required pumping speed and appropriately switches the vacuum modules on or off in a cascade. One of the COBRA NX screw vacuum pumps is frequency-controlled. It usually goes into operation first. Once it has achieved full capacity, the next vacuum pump is turned on and the frequency-controlled vacuum pump reduces its capacity if needed. If the pumping speed requirements increase, further vacuum pumps automatically switch on. This system works on a rolling basis. This means that the control system takes the operating hours of each individual vacuum pump into account and puts them into operation on an alternating basis so that all the pumps have the same number of operating hours.

Because the centralized vacuum system is installed in a separate room, there are no more adverse effects whatsoever in the workplace due to noise or heat emissions.

The vacuum system from Busch has been in operation since November 2016 and Thomas Giesecke and his team are very satisfied because all requirements for the new vacuum supply have been completely fulfilled. A further positive effect arose that no one necessarily had focused on when planning began: energy efficiency was increased considerably. Thomas Giesecke confirms that at least 50 percent energy savings were possible with the new vacuum system. This becomes apparent simply when one considers the total number of 36 rotary vane vacuum pumps that were previously in operation, as opposed to the six COBRA NX screw vacuum pumps in the new system. A seventh COBRA NX serves purely as a stand-by vacuum pump.
The forms for the smaller rotor blade components are still evacuated with existing rotary vane vacuum pumps. But now, these will be gradually connected to the new system, which is already designed for this in terms of capacity.

Reducing the number of vacuum generators is not the only aspect that enabled a drastic reduction in energy consumption; demand-based control also played a role. Previously, vacuum pumps were often operating 24 hours a day. Now, each individual screw vacuum pump has significantly shorter operating times.

This in turn reduces the maintenance required, which is already significantly less for screw vacuum pumps than for rotary vane vacuum pumps, minimizing maintenance costs. Maintenance can be performed during operation by disengaging the individual COBRA NX vacuum pumps and operating the stand-by vacuum pump in their places.

Gro



More information:
http://https://www.buschvacuum.com



Keywords (optional):



Company information / Profile:

Busch Vacuum Pumps and Systems is one of the world’s largest producers of vacuum pumps, vacuum systems, blowers and compressors.
Its extensive product portfolio comprises solutions for vacuum and overpressure applications in all industries, including the chemical, semiconductor, medical technology, plastics, and food sectors. It also covers the design and construction of customized vacuum systems, as well as a global service network.
The Busch group is a family-owned company and is still managed by the Busch family. Busch Vacuum Pumps and Systems has 3,000 employees in more than 60 companies in over 40 countries worldwide. Busch is headquartered in Maulburg, in southwest Germany. This is the location of Busch SE headquarters, as well as the German production facility and German sales company. In addition to Maulburg, Busch also has its own production plants in Switzerland, the UK, Czech Republic, Korea and the USA.

Busch Vacuum Pumps and Systems was founded by Dr.-Ing. Karl Busch and his wife Ayhan Busch in 1963. Dr.-Ing. Karl Busch developed the “Huckepack”, which was the first vacuum pump that could be used for vacuum packaging of foodstuffs. The follow-up product, the compact “R 5” rotary vane vacuum pump, revolutionized food packaging. A further milestone represented the development of the “COBRA” screw vacuum pump. In 1971 the international expansion of the Busch group started with the founding of a sales company in the UK. The first production plant outside Germany was established in the USA in 1979.

PressRelease by

Requests:

Jasmin Markanic

Busch Dienste GmbH
Global Marketing / Marketing Services
Coordinator Global Press & Media Relations

Schauinslandstraße 1
DE 79689 Maulburg
Phone: +49 7622 681 3376
Jasmin.Markanic(at)busch.de
www.buschvacuum.com



PressContact / Agency:



published by: SabrinaHeinecke
print pressrelease  send to a friend  

Date: 07/11/2019 - 05:57
Language: English
News-ID 1550653
Character count: 7924
Kontakt-Informationen:
Firma: Busch Dienste GmbH
Ansprechpartner: Jasmin Markanic Feedback to businesspress24.com about Pressrelease-id:
Stadt: Maulburg
Telefon: 0049 7622 681 3376

Meldungsart: Success
Versandart: send
Freigabedatum: 11.07.2019
Comments:



Number of hits: 292

Linking-Tips:



Direct Link to this PressRelease:






We would appreciate a link in your News-, Press- or Partner-Site.

Comments on this PressRelease






All members: 9 419
Register today: 0
Register yesterday: 1
Members online: 1
Guests online: 72


Don't have an account yet? You can create one. As registered user you have some advantages like theme manager, comments configuration and post comments with your name.