Galway Metals Intersects 4.7% Cu, 4.0% Zn, and 2.8 g/t Au over 2.7 metres at Estrades; Deep Drill Hole Commences
(firmenpresse) - TORONTO, ONTARIO -- (Marketwired) -- 06/14/17 -- Galway Metals Inc. (TSX VENTURE: GWM) (the "Company" or "Galway") is pleased to announce assay results from five additional drill holes completed at its 100%-owned, 20,915 hectare, Estrades polymetallic property located in the northern Abitibi of western Quebec, Canada. Galway is also currently undertaking the drilling of a deep drill hole that is targeting the down-plunge extension of the best mineralization identified on the property to date - below the former mine under the Main Zone. Galway has completed its Phase One drill program at Estrades, which was comprised of sixteen holes plus one wedge hole (one of the holes was stopped due to excessive deviation) for a total of 6,476 metres. The Phase One program was designed to expand the existing resource on the periphery of known zones at shallow depths, and to probe a few deeper holes close to potential source vents. Galway has received full assay results from 10 holes, with five of them previously reported in the and press releases. Assays for the remaining seven holes are pending.
Robert Hinchcliffe, President and CEO of Galway Metals, said, "Galway is pleased with results received to date from the Phase One drill program, and has begun its new 6,000 metre, Phase Two drill program. Phase Two is focused on the mostly undrilled area between the Central and Main Zones, and the deeper IP-generated targets below the Main Zone in the Company''s search for wider high-grade source vents."
Table 1: Highlights for the additional Phase One drill holes reported include:
Table 2: Highlights for the previously reported Phase One drill holes include:
See table above for all Notes except: hole GWM-17E-07 (DDS) intersected 1.1% Cu over 0.8m (0.5m TW) and 0.5% Zn over 2.5m (1.7m TW).
Deep Hole
Galway is also currently undertaking the drilling of a deep drill hole that is targeting the down-plunge extension of the best mineralization identified on the property to date - below the former mine under the Main Zone. This hole will target approximately 975 metres below surface (775 metres below the bottom of the ramp), and 200 and 366 metres below the deepest previous hole and wedge. One of the deep holes, hole H-116, intersected 1.7% Cu, 1.5% Zn, 0.5 g/t Au, and 33.2 g/t Ag over 8.9 m (TW = 7.3 m), including 4.2% Cu, 2.1% Zn, 1.3 g/t Au, and 54.1 g/t Ag over 2.4 m (TW = 2.4 m). It is thought that this may represent a potential source vent to the mineralization because of its higher copper grades and increased width of the zone.
Drill hole descriptions
Drill hole GWM-17E-06, which contained 15%-35% chalcopyrite plus good levels of sphalerite, was drilled 45 metres west of previously reported hole GWM-17E-05 in an area of the East Zone that was interpreted to have declining resource grades (Figure 1). Given the grade of hole GWM-17-06, the resource grade in this area should be increased. Drill hole GWM-17E-06 intersected 2.8 g/t Au, 111.3 g/t Ag, 4.0% Zn and 4.7% Cu over 2.65 metres (1.7m TW), including 7.8 g/t Au, 162.6 g/t Ag, 1.0% Zn and 11.2% Cu over 0.5 metres (0.3m TW) starting at a vertical depth of 309 meters.
Drill hole GWM-17E-14, which contained approximately 10% each chalcopyrite and sphalerite plus 40% massive pyrite, was drilled 440 metres west of hole GWM-17E-06 and 145 metres below previously reported hole GWM-17E-13 in an area that was outside the resource and returned 1.5 g/t Au, 121.0 g/t Ag, 6.0% Zn and 1.3% Cu over 2.7 metres (1.4m TW), including 2.5 g/t Au, 137.5 g/t Ag, 10.4% Zn and 0.7% Cu over 1.4 metres (0.7m TW) starting at a vertical depth of 236 meters. Given the high grades received, hole GWM-17E-14 should increase the resource in this area.
Drill hole GWM-17E-09, which intersected a fault and then massive pyrite followed by good levels of chalcopyrite and sphalerite, was drilled in a gap area between resource blocks in the East Zone. It is a shallow hole located 482 metres west of previously released hole GWM-17E-01 and 238 east of previously released hole GWM-17E-13. Given the grades encountered in hole GWM-17E-09, which were 0.4 g/t Au, 121.0 g/t Ag, 2.7% Zn and 0.9% Cu over 2.7 metres (1.8m TW), including 0.9 g/t Au, 166.7 g/t Ag, 7.8% Zn and 1.4% Cu over 0.5 metres (0.3m TW) starting at a vertical depth of 97 meters, Galway expects the resource to expand in this area. Galway is waiting for assays from nearby holes GWM-17E-10, GWM-17E-11 and GWM-17E-12 also drilled in the gap area to the west and below hole GWM-17E-09, plus deeper gap holes GWM-17E-19 and GWM-17E-19W drilled 530 metres and 474 metres, respectively, below hole GWM-17E-09.
Drill hole GWM-17E-02 intersected 0.6 g/t Au over 4.9 metres (3.0m TW), which may be the continuation of the high grade gold horizon intersected in hole GWM-17E-01. However, because it deviated 26 metres east and 42 metres down dip of its intended target, it was outside the plunge of high-grade mineralization.
Induced Polarization Geophysical Program
The Company has also completed a paired downhole induced polarization (IP) program at both its Estrades and nearby Newiska properties to search for deeper source vents rich in copper and other metals. This IP program is expected to enhance Galway''s ability to find areas rich in sulphides, which often hosts copper and other metal-bearing minerals. Galway has received results from this IP program and is interpreting these results in an effort to guide its deep drilling program in the search for wide, high-grade source vents. Initial plots show "very strong chargeability" responses in the vicinity of the deep drill holes below the workings and going west of hole H-116 (the Main Zone), and at Newiska off hole from hole NK 05 where an intersection of 0.34 g/t Au over 22.4 m was returned (TW unknown). According to RPA (2006), "this interval also averaged 259 ppm As, which is a common feature in gold-rich VMS systems. This mineralized zone is therefore considered as an indication of potential for a gold-rich massive sulphide deposit in the property."
Estrades Resource Estimate
On , the Company announced that it had consolidated 100% of the Estrades mining camp, which includes approximately 17, 16, and 31 km along the Estrades, nearby Newiska and Casa Berardi trends, respectively. Galway simultaneously released the results of an updated NI 43-101 compliant Estrades resource estimate carried out by Roscoe Postle Associates (RPA), which resulted in an approximate four-fold increase in resource tonnes. The updated resource was filed on Sedar on October 3, 2016. A summary of the new resource is provided below. Breakwater Resources Ltd. spent CDN$20 million in 1990 developing Estrades, including the installation of a 200 metre deep by 150 metre along strike decline, a ventilation raise and associated infrastructure. Production in 1990-91 totalled 174,946 tonnes grading 12.9% Zn, 6.4 g/t Au, 1.1% Cu and 172.3 g/t Ag. Breakwater closed the mine amid weak metal prices.
Table 3: Mineral Resource Summary, Estrades Project, August 12, 2016
Notes:
Table 4: Galway Metals'' Mineral Resource Statement, Clarence Stream and Estrades
Clarence Stream Notes; Refer to Estrades Notes for the Estrades Mineral Resource portion of the Galway Metals Resource Statement
Estrades, Newiska, and Casa Berardi Geology and Mineralization
The Estrades area is in the NW Abitibi Subprovince, with generally east-west striking and vertically dipping volcanics, with the mineralization of a classic Archean age of the syngenetic exhalative type, hosted in a rhyolite felsic schist and/or brecciated or felsic tuff with alteration typically a pervasive sericite with local chlorite. Regional metamorphism is of greenschist facies. Pyrite is the dominant sulphide, however sphalerite is common, as is chalcopyrite and galena. RPA found that 2 mineralized horizons appear to be kept separate by a Key Marker horizon; the two layers traceable along the entire strike length. To the west, the Main Zone is mineralized for greater than 400 m horizontally, extends greater than 850 m below surface, has an average width of 3.8 m, and is the location of all production to date. The Central Zone has a strike length of 500 m, is drilled to 550m, and has an average width of 2.0 m, while the East Zone lies 100 m east of the Central Zone, is greater than 700 m horizontal, is drilled to 750 m in depth, and is 1.0 m to 2.5 m in width. A fault separates the Main Zone from the Central and East Zones, and strikes 338 degrees and dips 65 degrees SW, with a 210 m offset. Mineralization that has been identified in the deepest drill hole (Hole H-281AW) is located under the mine, and intersected sulphide mineralization 900 m below surface, returning 3.3% Zn, 0.5% Cu, 1.1 g/t Au and 38.7 g/t Ag over 1.9 m. The Estrades deposit is covered by glacial silt, clays and sandy gravels of variable thickness. The Newiska Block is greater than 300m of sericite-chlorite alteration in rhyolite, with chalcopyrite-sphalerite stringer mineralization and is located southeast of Estrades. The Casa Berardi geology and mineralization consists of a major regional deformation zone, the Casa-Berardi Break, that is 2 km north of the Estrades Unit within sediments, and that is a 4m graphitic fault with injections of quartz-carbonate veining in sandstone, siltstone, greywacke and argillite +BIF, where the sediments are sericitized and carbonatized; containing up to 20% ankerite and locally, pyrite, arsenopyrite-bearing, smoky to dark quartz veins containing pyrite and arsenopyrite.
Review by Qualified Person, Quality Control and Reports
In compliance with National Instrument 43-101, Mr. Mike Sutton, P.Geo., Chief Geologist and a director of Galway, is the Qualified Person responsible for the accuracy of this news release. Mr Reno Pressacco, P. Geo, a consultant with RPA, is the Qualified Person responsible for preparation and disclosure of the Estrades Mineral Resource estimate, and is independent of Galway. The drill core is sawn in half with one half of the core sample shipped to Swastika Laboratories situated in Swastika, ON, which has accreditation of ISO/IEC 17025. The other half of the core is retained for future assay verification. Other QA/QC measures includes the insertion of certified reference standards (gold and polymetallics) and blanks into the sample stream, and the regular re-assaying of pulps and rejects at alternate certified labs. Gold analysis is conducted by fire assay using atomic absorption or gravimetric finish for samples greater than 10 g/Mt gold. Other Metals (Ag, Cu, Pb, Zn, Co, As) have full acid digestion and analyzed by AAS; with over limits (5000 PPM) analyzed by AAS using method dilutions, and the Silver (Ag) over limits (greater than 200 ppm) analyzed by fire assay (FA) & gravimetric finish. The laboratory re-assays at least 10% of all samples and additional checks may be run on anomalous values.
Table 5: Drill Hole Coordinates
About the Company
Galway Metals is well capitalized with two gold projects in Canada, Clarence Stream, an emerging gold district in New Brunswick, and Estrades, the former producing, high-grade VMS mine in Quebec. The Company began trading on January 4, 2013, after the successful spinout to existing shareholders from Galway Resources following the completion of the US$340 million sale of that company. With substantially the same management team and Board of Directors, Galway Metals is keenly intent on creating similar value as it had with Galway Resources.
CAUTIONARY STATEMENT: Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy of this news release. No stock exchange, securities commission or other regulatory authority has approved or disapproved the information contained herein.
This news release contains forward-looking information, which is not comprised of historical facts. Forward-looking information involves risks, uncertainties and other factors that could cause actual events, results, performance, prospects and opportunities to differ materially from those expressed or implied by such forward-looking information. Forward-looking information in this news release includes statements made herein with respect to, among other things, the Company''s objectives, goals or future plans, potential corporate and/or property acquisitions, exploration results, potential mineralization, exploration and mine development plans, timing of the commencement of operations, and estimates of market conditions. Factors that could cause actual results to differ materially from such forward-looking information include, but are not limited to, exploration results being less favourable than anticipated, capital and operating costs varying significantly from estimates, delays in obtaining or failures to obtain required governmental, environmental or other project approvals, political risks, uncertainties relating to the availability and costs of financing needed in the future, changes in equity markets, inflation, changes in exchange rates, fluctuations in commodity prices, delays in the development of projects, risks associated with the defence of legal proceedings and other risks involved in the mineral exploration and development industry, as well as those risks set out in the Company''s public disclosure documents filed on SEDAR. Although the Company believes that management''s assumptions used to develop the forward-looking information in this news release are reasonable, including that, among other things, the Company will be able to identify and execute on opportunities to acquire mineral properties, exploration results will be consistent with management''s expectations, financing will be available to the Company on favourable terms when required, commodity prices and foreign exchange rates will remain relatively stable, and the Company will be successful in the outcome of legal proceedings, undue reliance should not be placed on such information, which only applies as of the date of this news release, and no assurance can be given that such events will occur in the disclosed time frames or at all. The Company disclaims any intention or obligation to update or revise any forward-looking information contained herein, whether as a result of new information, future events or otherwise, except as required by applicable securities laws.
Contacts:
Galway Metals Inc.
Robert Hinchcliffe
President & Chief Executive Officer
Toll Free: 1-800-771-0680
Themen in dieser Pressemitteilung:
Unternehmensinformation / Kurzprofil:
Datum: 14.06.2017 - 04:30 Uhr
Sprache: Deutsch
News-ID 1509012
Anzahl Zeichen: 3383
contact information:
Contact person:
Town:
TORONTO, ONTARIO
Phone:
Kategorie:
Mining & Metals
Typ of Press Release:
type of sending:
Date of sending:
Anmerkungen:
Diese Pressemitteilung wurde bisher 188 mal aufgerufen.
Die Pressemitteilung mit dem Titel:
"Galway Metals Intersects 4.7% Cu, 4.0% Zn, and 2.8 g/t Au over 2.7 metres at Estrades; Deep Drill Hole Commences
"
steht unter der journalistisch-redaktionellen Verantwortung von
Galway Metals Inc. (Nachricht senden)
Beachten Sie bitte die weiteren Informationen zum Haftungsauschluß (gemäß TMG - TeleMedianGesetz) und dem Datenschutz (gemäß der DSGVO).
