KOYO Bearing Inspection And Cleaning Process
BEST Bearing Co.,Ltd(HONGKONG)Was Established At 2001. We are kown for Best Bearings – TIMKEN Bearings . As Now Had Been With Over More Than Ten Years Experience In Exported Brand Bearings’ Business.
(firmenpresse) - BEST Bearing Co.,Ltd(HONGKONG)Was Established At 2001. We are kown for Best Bearings - TIMKEN Bearings . As Now Had Been With Over More Than Ten Years Experience In Exported Brand Bearings' Business.The Main Brand In Export Include SWEDEN SKF Bearings. Germany FAG And INA Bearings. USA TIMKEN Bearings. Japan NSK. NTN. NACHI. ASAHI. IKO. NMB Bearings And So On.
About KOYO Bearing Inspection:
When KOYO Bearing was installed properly, Regular Inspection is necessary to confirm its normal work .Most Importantly, KOYO bearing Should be make sure installed properly, flexible rotation, no card lag phenomenon, such as bearing improperly installed, can make the bearing temperature rise quickly and damage, even bearing jammed fracture and other major accidents.
How to carry on regular inspection of KOYO Bearing ,There are three steps need to following up:
First, If the bearing with a stethoscope and check has the strong metal noise, such as vision, irregular note that exception. Its reason has poor lubrication, shaft or precision bearing, bearing damage, foreign body intrusion, etc.
Second, bearing temperature, it can be make conclusion if the bearing has something wrong as per the average external temperature of the bearing. But using the oil hole directly measure the temperature of the bearing outer ring more accurate. Bearing temperature, from the beginning of the operation, usually 1 ~ 2 hours after the temperature stability. If the bearing installation, the temperature will rise sharply, abnormal high temperature. The reason such as lubricant, bearing clearance is too small, too much bad installation, sealing device too much friction, etc. High-speed rotation, the ways of choosing bearing, the lubrication fault are also the reasons in the process of KOYO Bearing Inspection.
Third, the small KOYO bearing can rotate with the hand, to confirm whether the KOYO bearing rotate smoothly. Check project has caused by foreign bodies, scars, creasing seized up, due to the bad installation, installation of seat processing bad moment is not stable, because the clearance is too small, installation error, and seal friction caused by the torque is too big, and so on. If there is no abnormal situation, the KOYO bearing can start operation as usual.
About KOYO Bearing Cleaning:
Generally, Electric Motor will be cleaning and Refuel after 2,000 Hours, There are two ways about How to Clean KOYO Bearing:
1), Hot oil Cleaning Methods
KOYO bearing with Soft dry oil or rust cream hardening, should dip in 100-200 ¡æ hot oil, clamp with forceps KOYO bearing, using hair brush cleaning KOYO bearing Which Should immersed into Hot oil. When Soft dry oil or rust paste be heated to 100-200 ¡æ It will be melt, it is easy to flush out from a crack in the KOYO bearing. Sometimes as long as KOYO bearing was repeatedly shaking in the oil, the oil dirt will flow away from crevices.
In cleaning the centripetal spherical bearing of the motor, you should put the ball, pearl frame transverse transfer from the outer ring, internal ring into hot oil, again after a short cylindrical roller bearing when cleaning roller, beads, also should be the inner ring and outer ring off.
When cleaning in the hot oil, the oil temperature should not exceed 200 ¡æ.If use flame directly heating, should pay attention to prevent the oil burning, KOYO bearings to hang in the pan, sink will cause overheating and reduce hardness.
2), Common Cleaning Method
Put KOYO bearing soak 5-10 minutes of kerosene to squeeze the inner ring with one hand, another hand turn the outer ring, KOYO bearing on dry oil or antirust cream will fall down.
Then put KOYO bearing in cleaner kerosene, with soft hair brush to wash, wash oil inside the ball and crack, put them in gasoline cleaning, and put out with clean paper. Centripetal spherical ball bearing and short cylindrical roller bearing when cleaning should be ball, pearl, the inner ring and outer ring off to clean.
Mounted on the shaft of KOYO bearings cleaning, relied on pour oil or oil gun spraying method, easy to wash off the oil with kerosene after first use gasoline; Difficult to clean off of oil, first in 100-200 ¡æ hot oil leaching or oil gun spraying, and then clean with gasoline.
It is important to note that don't use a sharp tool to scrape, KOYO bearing oil dirties or corrosion of hard, so as not to damage the KOYO bearing ring parts of the finish rolling body and groove, wash KOYO bearing with a clean dry cloth.
Therefore , KOYO Bearing need to be inspect and clean regularly ,But If No Proper Inspect and Cleaning Steps ,It can only waste time and energy ,Thus It is important to follow up the below steps to inspect and clean KOYO Bearing to confirm its long service .
Hong Kong BEST Bearing Co.,Ltd
Email: sales(at)best-bearings.com
MSN: sales(at)best-bearings.com
SKYPE: best.bearing
Website: http://www.bearing-us.com/
Themen in dieser Pressemitteilung:
Unternehmensinformation / Kurzprofil:
Datum: 21.05.2014 - 04:45 Uhr
Sprache: Deutsch
News-ID 1298332
Anzahl Zeichen: 0
contact information:
Contact person: KOYO Bearing
Town:
China
Phone: 0
Kategorie:
Machinery & Tools
Anmerkungen:
Diese Pressemitteilung wurde bisher 232 mal aufgerufen.
Die Pressemitteilung mit dem Titel:
"KOYO Bearing Inspection And Cleaning Process
"
steht unter der journalistisch-redaktionellen Verantwortung von
Hong Kong BEST Bearing Co.,Ltd (Nachricht senden)
Beachten Sie bitte die weiteren Informationen zum Haftungsauschluß (gemäß TMG - TeleMedianGesetz) und dem Datenschutz (gemäß der DSGVO).
